What Are Weep Holes | Need for Weep Holes | Foundation Weep Holes | Types of Weep Holes | Weep Holes In Retaining Wall | Window Weep Holes
Introduction of Weep Holes
Water is the biggest enemy of this structure. It is necessary to remove water from the structure as far as possible to prevent it from any further damages.
There are many chances of entering water into the structure but the weep holes function is to pass water through it outside the structure.
Weep holes are a small opening that is in a rectangular or circular shape that allows water to drain through it.
Weep holes are mostly provided in the wing walls retaining walls masonry walls extra to remove water through it.
In this article you will get to know about weep holes and its importance.
Open head joint peoples are provided by Living out water from the joints. These types of weep holes are open holes of the same size as the typical spacing of the joints.
The open head joint process is one of the common and effective methods which are used to evaporate water from the cavity. Depressing which is provided between the open hip joint weep holes is 24 inches.
Cotton rope wicking weep holes are formed by using the rope of 12 inches in length. This type of weep holes are placed in the joints and the other end is extended to the cavity wall.
The water from the back of the wall is absorbed by the Cotton and on the other side, it gets evaporated. This process is low as compared to other types of weep holes.
Tube wells are formed with the help of hollow plastic or metal tubes which are spaced around 16 inches from each other. The Tube weep holes are installed at a slight angle to allow water to drip out easily and care should be taken that the angle should not be too steep.
Sometimes a Shallow layer of gravel is laid to prevent the water from dropping from the blockage of the tube weep holes.
Corrugated channels are the latest technology in the weep holes which helps to quickly drain off water from the multiple channels. It is installed at the bottom side of the bed joint of the mortar.
Weep holes are provided at the bottom of the retaining walls which have to remove the hydrostatic pressure which is developed.
Weep holes are small openings that are in a circular or square shape. Weep holes play a crucial role in the retaining wall to drain water from the retaining wall and decrease the hydrostatic pressure on the walls.
Weep holes in the retaining wall prevents the damage of the wall and dampness on the wall. Weep holes in the retaining wall main consist of clay, plastic, or the metal pipe which is extending through the retaining wall to the layer of porous backfill.
The window peoples are provided on the bottom side of these window frames. The window peoples act as a drainage system for your Windows.
If the window weeps holes not draining properly then there may be chances of any blockage due to debris, paint, or any other element. It is very necessary to regularly maintain the window weep holes for its efficient functioning. Weep holes in shower are also provided to drain out water through it.
Check window weep holes at least once a year before the rainy season. If the window weep holes are blocked then open them with the brush or screwdriver and clean it properly.
If there are no weep holes is provided in the windows then you can install weep holes in windows at your home. You can make some holes with a drill into the window frame at the bottom side which will help to drain out rainwater and acts as a weep hole.
when the weep holes are constructed in the brick masonry, the mortar between the successive courses of the brickwork may drop down in the weep holes which can cause the blockage of the weep holes. It is necessary to regularly maintain and clean the weepholes in Brickwork for its proper functioning.
Weep holes are small opening which can provide access to the insects and small rodents. This can also block the weep holes to prevent this problem baffled vents are installed.
Open Head Joint Weep Holes: The open head joint process is done by leaving out mortar from the joints. This create open holes of the same size of the typical spacing of the joints. This is the most common method and most effective way to evaporate water from the cavity. The spacing between open head joints can be done at every 24 inches (61 cm)
Cotton Rope Wicking Weep Holes: These type of weep holes are formed by using a rope of up to 12 inches in length. This is placed in the joints and the other end is extended up to the cavity wall. The water from the back of the wall is absorbed by the cotton and the on the other side it is evaporated
Tubes Weep Holes: Weeps, or weep holes are used to drain water through a wall. Weep tubes line weep holes to ensure that draining water does not damage the surrounding wall with erosion over time. Made in standard sizes with durable plastic materials, weep holes can also be plugged or screened with ease to regulate drainage.