16 Definition Related for Plastering Work | Tools For Plastering | Preparation of Background for Plastering

Definition Related for Plastering Work

Plasterwork is construction or ornamentation done with plaster, such as a layer of plaster on an interior or exterior wall structure, or plaster decorative mouldings on ceilings or walls.

The process of creating plasterwork, called plastering or rendering, has been used in building construction for centuries.

Plaster work-related definition as below

1. Plaster Background.
2. Plaster Blistering.
3. Cracking in Plaster.
4. Crazing in Plaster.
5. Dado in Plaster.
6. Dubbing coat in Plaster.
7. Dost in Plaster.
8. Finishing Coat Plaster.
9. Flaking Plaster.
10. Gauging in Plaster. 
11. Grinning in Plaster.
12. Grounds in Plaster.
13. Hacking for Plaster.
14. Keys in Plaster.
15. Laitance Plaster.
16. Peeling in Plater.
17. Undercoat Plaster. 

1. Plaster Background

It is the surface of masonry or any other surface to which we apply first coat plaster.

2. Plaster Blistering

As soon as you can feel a blister developing, apply a plaster. An Elastoplast SOS Blister Plaster is one of the first self-help options.

A plaster will cushion the affected area and protect even an open blister from infection and dirt. It will also help take off the pressure-induced pain and help the healing process.

3. Cracking in Plaster

These are cracks developed on the plastered surface due to the movement of background or structure surrounding it.

Cracks in the plaster may result due to different reasons: Evaporation if the wall is not protected from sun and wind which can cause map cracking or dry shrinkage cracks.

Suction into the walls if the blocks are absorbent and they have not been dampened which might cause drying shrinkage cracks.

4. Crazing in Plaster

Hair cracks develop on the finished surface in an irregular pattern called crazing. Crazing is a network of fine cracks, usually in a hexagonal pattern, which measures between 5 and 75 mm across each hexagon.

Crazing often occurs within a few hours of the plaster being applied to the wall and cracks may hardly be visible until dust or moisture makes them noticeable.

5. Dado in Plaster

Dado is a special treatment given to the lower part of wall so that the wall can with-stand erosive forces. Dado rail, or chair rail, is a type of moulding fixed horizontally at roughly one-third the ceiling height to the wall around the perimeter of a room.

Our Dado Rails are made from high-quality plaster in a variety of styles suited to all types of rooms.

6. Dubbing Coat in Plaster

Before applying plaster, the hollow spaces in the solid background are filled. This process is called the dubbing coat process.

Dub-out the walls with the haired base-coat plaster (in coats not greater than 9mm) were necessary to create an even surface for the first or scratch coat (so that each subsequent coat of lime plaster can then be applied at the same thickness), this should be left to harden before applying the first coat.

7. Dots in Plaster

Small projection laid on background for fixing screeds etc. is called dots. It is size may be 150 mm x 150 mm
At one end of the wall we stick two small pieces of flat wood (thin ply) on some blobs of plaster; one near the top of the wall, and one near the bottom. These are the “Dots“.

8. Finishing Coat Plaster

It is the final coat of plaster. Such a coat is known as setting a coat or skimming coat.

9. Flaking Plaster

A solution would be to scrape off the flaking parts over a slightly larger area, re-plaster that area and apply a primer coat once the plaster has completely dried. Only then should you repaint either the whole wall or just that portion.

10. Gauging in Plaster

Gauging Plaster is designed for use with finish lime. It is specially ground, calcined gypsum, which readily mixes with water and lime putty.

A finish coat of gypsum gauging plaster and finish lime is designed primarily for interior smooth trowel application over a gypsum plaster basecoat.

11. Grounds in Plaster

These are wooden strips. These strips are fixed to the background in which the primary finishing coat may be secured.

12. Hacking for Plaster

The process in which the surface of the background is roughened to provide a suitable key for plastering is called hacking.

Hacking refers striking of surfaces such as RCC walls, columns, beams, slabs etc., with a chisel to dent the surface in order to create a proper mechanical bond with cement mortar/gypsum plaster directly applied on it.

13. Keys in Plaster

The opening or indentations or corrugation on the background or surface of undercoat from mechanical bound with plaster is called a key.

14. Laitance Plaster

A screen consisting of particles thin layer of fine cement particles is formed due to excessive trowelling or freshly laid concrete. It is called laitance.

15. Peeling in Plater

Peeling from plaster could be a result of insufficient wet troweling of the white coat when the plaster was originally applied, causing chalking of the surface. Very hard plaster may be slick, reducing the adhesion of any coating.

16. Undercoat Plaster-

All the coats of plaster applied under the finishing coat are called undercoat.

Also, Read: What Is Plaster | Methods of Plastering

Tools For Plastering

Following tools are used for plastering:

• Trowel.
• Float.
• Floating Rule.
• Plumb Bob.

1. Trowel

Trowels used for mixing mortar. Trowels are 150 mm to 450 mm. A few of the above are blunt-ended, and a few are point-ended. A trowel is a small hand tool used for digging, applying, smoothing, or moving small amounts of viscous or particulate material.

2. Float

A float is used for spreading the motor on the surface of the wall. It can be of metal or wood. Wooden float is prepared by fixing the handle on a 10 mm thick wooden board. It is used to finish the coat. It is called skimming float.

Also, read: What Is Classification of Bricks | Classification of Bricks Different Base 

3. Floating Rule

It is used for checking the level of the plastered surface between successive screens. Floating Rules are a special type of advanced rule that can perform complicated actions not possible with rules on interface or group tabs. Floating rules can act on multiple interfaces in the inbound, outbound, or both directions.

4. Plumb Bob

It is used for vertically of the plaster. Over and above this, spirit level, brush, set square, etc. are used for plastering. A plumb bob, or plummet, is a weight, usually with a pointed tip on the bottom, suspended from a string and used as a vertical reference line, or plumb-line. It is a precursor to the spirit level and used to establish a vertical or horizontal datum.

Preparation of Background for Plastering

1. Before applying plaster on the surface of the wall, all the masonry joints are raked out to a depth of 10 mm. in brick masonry and increase of stone masonry up to 15 mm, joints are raked out.
2. The racking out of joints provide the key to the plaster all dirt like dust and mortar droppings, etc. should be cleaned with a wire brush.
3. All uneven surfaces are levelled before rendering is applied. The surface should be washed with clean water and kept damp uniformly.
4. In case the plater is to be applied on the old surface, the surface should be cleaned. Old loose plaster should be broken surface should be washed with water, and joints should be racked out.

Also, read: What Is Quarrying of Stones | Methods of Quarrying | Selection of a Site for Quarrying of Stones

 Methods of Plastering

1. Three coat plaster
   • Application of rendering coat
   • Application of floating coat
   • Application of finishing coat
2. Two coat plaster
3. Single coat plaster
4. Cement Plaster and Cement Lime Plaster
5. Plaster on lath
   • Wooden laths
   • Metal laths

---