What Is Self Compact Concrete?
Important Point
Making concrete structures without vibration has been done in the past. For example, the placement of concrete under-water is done by the use of tremie without vibration.
Shaft concrete and mass concrete may be successfully placed without vibration.
But the above examples of concrete are normally of lower strength and difficult to obtain consistent quality.
Modern application of SCC (self-compacting concrete) is focussed on high performance, better and more reliable, and uniform quality.
List of Test Methods for Workability Properties of Self Compacting Concrete (SCC).
1. Slump flow by Abrams cone.
2. T50 cm Slump flow
3. J-ring
4. V-funnel
5. V-funnel at T5 minutes
6. L-box
7. U-box
8. Fill-box
9. GTM Screen Stability Test
10. Ouimet
In this article, we are discussion & Procedure Slump Flow Test
Also, read: Types of Plaster Finishes (List of Plaster Finishing)
Slump Flow Test.
What Is Slump Flow Test?
The slump flow test is done to assess horizontal flow of concrete at the absence of obstructions. It is the most commonly used test and gives a good assessment of filling ability. It may be used at the site. The test also indicates the resistance to segregation.
Equipment for Slump Flow Test
• Slump Cone
The usual slump cone having a base diameter of 200 mm, top dia. 100mm, and height 300mm are used.
• Base Plate For Slump Flow test
A stiff base plate square in shape is having at least a 700 mm side. Concentric circles are marked around the center point where the slump cone is to place. A firm circle is drawn at 500 mm diameter
• A trowel
This tool is used to place cement mortar.
• Scoop
This use in QC department for the material.
• Measuring tape
To measure the length.
• Stopwatch
Use for time record
Also, read: What is CBR Test in Civil
Procedure of Slump Flow Test
- About 6 liters of concrete is needed for this test.
- Place the baseplate on level ground.
- Keep the slump cone centrally on the base plate.
- Fill the cone with the scoop.
- Do not tamp.
- Simply strike off the concrete level with the trowel.
- Remove the surplus concrete lying on-base place.
- Raise the cone vertically and allow the concrete to flow freely.
- Measure the final diameter of the concrete in two perpendicular directions and calculate the average of the two diameters.
- This is the slump flow in mm.
- Note that there is no water or cement paste or mortar without coarse aggregate is seen at the edge of the spread concrete.
Also, read: What Is Inverted Beam | Advantages of Inverted Beam | Purpose of Inverted Beam
Calculations of Slump Flow Test
Largest diameter of slump flow (dm) = _______ mm
Diameter perpendicular to largest diameter (dr) = _______ mm
Slump flow = (dm+dr) /1
Results of Slump Flow Test
The slump flow of Self compacting concrete is _______ mm
Interpretation of Slump Flow Test
The higher the flow value, the greater its ability to fill formwork under its own weight.
A value of at least 650 mm is required for SCC (Self Compact Concrete).
In case of severe segregation, most coarse aggregate will remain in the center of the pool of concrete and mortar and paste at the periphery of concrete.
T50 Slump Flow Test
The procedure for this test is same as for slump flow test. When the slump cone is lifted, start the stopwatch and find the time taken for the concrete to reach a 500 mm mark.
This time is called T50 time.
This is an indication of the rate of spread of concrete.
A lower time indicates greater flowability.
It is suggested that T50 time may be 2 to 5 secs.
Like this post? Share it with your friends!
Suggested Read –
- West Point Bridge Designer
- Introduction of USCS | USCS Classifies Soils into Two Broad Categories
- Introduction of Gantry Girder | Load on Gantry Gutter | Type of Load on Gantry Gutter
- What Is Pier Foundation | Types of Drilled Piers | Advantages and Disadvantages of Drilled Pier Foundations
- What Is Self Compact Concrete | History of SCC | Advantages & Disadvantages of (SCC) Self Compacting Concrete
Originally posted 2020-08-04 01:23:05.
Leave a Reply