Classification of Stone Work | What Is Stone Masonry

What Is Stone Masonry?

The construction of stones bonded together with mortar is termed as stone masonry. Where the stones can be found in abundance in nature, on cutting and dressing to the proper shape, they provide an economical material for the construction of various building components such as walls, columns, tootings, arches, beams, etc..

Stone-masonry being stronger, durable, and weather-resistant, when compared with brick masonry, is used in the construction of piers, docks, dams lighthouse, and other marine structures.

Classification of Stone Work

Based on the arrangement of stones in the construction and the degree of refinement in the surface finish, the stone masonry can be classified broadly into the following two categories:

1. Rubble Masonry
   1. Coursed Rubble
   2. Uncoursed Rubble
   3. Random Rubble
   4. Dry Rubble
   5. Polygonal Rubble
   6. Flint Rubble
2. Ashlar Masonry 
   1. Ashlar Fine
   2.  Ashlar rough tooled 
   3. Ashlar rock or quarry faced 
   4. Ashlar Chamfered 
   5.  Ashlar block-in course

Also, read: What Is Concrete | 31 Different Types of Concrete

1. Rubble Masonry

In this type of construction, stones of irregular size are used. The stones as obtained from the quarry are taken to be used in the same form or are broken and shaped into suitable sizes by means of a hammer as the work proceeds. The strength of the rubble masonry mainly depends on:

• The quality of the mortar.
• The use of long stones at a frequent interval for proper bonding.
• The proper filing of the mortar between the spaces of stones.

1.1. Coursed Rubble Masonry

In this type of rubble masonry, the heights of stones vary from 50 mm to 20 cm. The stones are stored before the work commences.

The masonry work is then carried out in courses such that the stones in a particular course are of equal heights.

This type of masonry is used for the construction of public buildings and residential buildings. The coursed rubble masonry is further divided into three categories.

1.2. Coursed Rubble Masonry I Sort

In this type, stones of the same height are used, and the courses are of the same height. The face stones are dressed by means of a hammer, and the brushings do not project by more than 40 mm. The thickness of the mortar joint does not exceed 10 mm

Coursed rubble masonry I Sort

1.3. Coursed Rubble Masonry H Sort

The stones to be used are of different heights. The courses need not be of equal heights. Only two stones are to be used to make up the height of one course. The thickness of the mortar joint is 12 mm

Coursed rubble masonry II Sort

1.4. Coursed Random Rubble III Sort:

The stones to be used arc of different heights, the minimum being 50 mm. The counts need not be of equal heights. Only three stones are to be used to make up the height of one course. The thickness of the mortar joint is 16 mm.

Coursed rubble masonry III Sort

1.5. Uncoursed Rubble Masonry

In this type of rubble masonry, the stones arc not dressed. However, they arc used as they arc available from the quarry, except by knocking out some corners. The courses arc not maintained regularly.

The larger stones are laid first, and the spaces between them are then filled by means of spalls. The wall is brought to a level every 30-50 cm.

This type of rubble masonry being cheaper is used for the construction of compound walls, garages, labor quarters, etc.

Uncoursed Rubble Masonry

1.6. Random Rubble Masonry

In this type of rubble masonry, stones of irregular sizes and shapes are used. The stones are arranged to have a good appearance.

It is to be noted that more skill is required to make the masonry structurally stable. If the face stones are chisel dressed and the thickness of mortar joints does not exceed 6 mm, it is known as random rubble masonry, I sort.

If the face stones are hammer dressed and the thickness of mortar joints does not exceed 12 mm, it is known as random rubble masonry II sort. This type of masonry is used for the construction of residential buildings.

Random Rubble Masonry

1.7. Dry Rubble Masonry

This is just similar in construction to the coursed rubble masonry III sorts except that no mortar is used in the joints. This type of construction is the cheapest, but it requires more skill in construction.

It is extensively used for compound walls pitching on bridge approaches, retaining walls, etc. In order to prevent the displacement of stones and to make the work more stable, the two courses at the top and about 50 cm length at the ends are sometimes built in mortar.

1.8. Polygonal Rubble Masonry

In this type of masonry, the stones are hammer dressed and the stones selected for face work are dressed in an irregular polygonal shape.

Thus, the face joints are seen running in an irregular shape in all directions. It is to be noted that more skill is required in this type of construction.

1.9. Flint Rubble Masonry

In this type of masonry, the stones are used as flints that are irregularly shaped nodules of silica. The width and thickness vary from 80 mm to 15 cm and the and the length varies from 15 to 30 cm.

Also, read: What Is Standard Proctor Test & his Detail | Procedure Standard Proctor Test

2. Ashlar Masonry 

This is costlier, high grade and superior quality masonry. This is built from accurately dressed stones with uniform and very fine joints of about 3 mm thickness.

By arranging the stone blocks in various patterns, different types of appearances can be obtained. The backing of ashlar masonry walls may be built of ashlar or rubble masonry.

2.1. Ashlar Fine Masonry

At all beds, joints, and faces stones should be dressed perfectly so that they conform to the desired pattern. The size of the stones to be laid in regular courses should not be less than 300 mm in height.

The width of the stones should not be less than the height of the course, In addition, the length of the stones should be more than two times the height of the course.

Generally, face stones arc laid as headers and stretchers alternatively. The header comes under the middle portion of the stretchers.

In order to break the continuous vertical joints, the stones in the adjacent layers should have a lap of more than half of the height of the course.

All the joints, either horizontal or vertical, should be made of fine mortar with a maximum thickness of 3 mm. The broken edges of the stones should not be visible at the joints.

Ashlar Fine Masonry

2.2. Ashlar Rough Tooled Masonry

The exposed faces of this type of masonry should be given a fine dressed chisel drafting of about 25 mm width. In between the drafts, portions should be roughly tooled. The joint thickness should be 6 mm.

2.3. Ashlar Rock or Quarry Faced Masonry

In this case, the exposed faces of the facing stones between the chisel draftings all around are left undressed. However, the projections of sizes more than 8 cm arc broken.

All other specifications regarding the sizes of the stones and the bond are kept similar to that of ashlar rough tooled masonry.

2.4. Ashlar Chamfered Masonry

In this type of ashlar masonry, the strip is provided as above. However, it is chamfered or beveled at an angle of 45 degrees by means of a chisel for a depth of about 25 mm.

Another strip 12 mm wide is then provided on the remaining exposed face of the stone and the surface inside this strip is left in the same form as received from the quarry.

The large bushings projecting out to more than 80 mm is removed by a hammer. A neat appearance of the grooved joints is obtained with the help of this type of construction.

2.5. Ashlar block-in course Masonry

This type of masonry occupies an intermediate position between the rubble masonry and ashlar masonry. The faces of the stones are generally hammer dressed and the thickness of mortar joints does not exceed 6 mm.

The depth of courses varies from 20 to 30 cm. This type of construction is used for heavy engineering works.

Also Read: Stone Classification

---

Originally posted 2023-06-03 11:00:48.